How To Set Up Kenmore Water Softener

We've put together a Kenmore Water Softener Ultimate Guide to help you troubleshoot whatsoever bug y'all might be having with your softener.

Since Sears has closed and you tin can no longer accept your product direct into a shop for maintenance or repair, we can help.

You can trust WaterSmart to service your Kenmore water softener in Southern Ontario, as we take been proudly servicing Kitchener, Waterloo, Cambridge and Guelph for 25 years.

This guide will give you solutions to some of the virtually common problems yous might encounter, as well as maintenance and service tips. So, permit'southward get started!

Detect help with DIY repairs on your Kenmore water softener or contact WaterSmart for expert assistance!

Chapter ane: How to Set up Salty Water Problem

There are a number of reasons why your h2o may outset to gustatory modality salty. These include:

• H2o Softener Tank Is Flooded

• Your Entry Valve Is Damaged

• Your Float Levels May Exist Likewise Loftier

Water Softener Tank Is Flooded:

If your water starts to taste salty and in that location is alkali coming through your lines and plugging up your faucets, your water softener tank may exist flooded and not draining properly. This could be happening if your safety float is sticking.

Solution:

Step 1: Remove the lid of your h2o softener.

Step 2: Remove the hat off of your salt level indicator tube; your condom bladder is located inside of this cylinder.

Stride three: Pull out your safety bladder mechanism that is inside of the cylinder.

Step 4: Accept your prophylactic bladder autonomously with a pocket-size screwdriver.

Footstep v: Run the pieces of your rubber float under some hot water for a few minutes to remove any clogs or debris. While information technology is being run under the water, gently move the bladder up and down to make sure that it is moving freely.

Step 6: Check to come across if the modest ball in the bottom of the float is able to motion freely likewise.

Note: Only attempt to remove and clean your safety float when your water softener is not in a regeneration mode.

The post-obit video will show you in greater detail how to exercise these steps.

Kenmore water softener repair Kitchener - learn how to clean your condom float

Your Entry Valve Is Damaged:

Yous may as well be getting salty water if your entry valve is damaged, clogged or cleaved. The entry valve, which is usually located at the back of your unit, controls the water coming into your softener.

Solution:

If your entry valve is cleaved or damaged, y'all will need to contact a professional to replace it.

Your Float Levels May Be Too Loftier:

Another reason why y'all may be getting salty h2o is that your float levels may be as well high. If this happens, then too much water volition be filling upward your brine tank.

Solution:

Check your bladder levels and see if they are set too high. If they are, adjust them to a lower level.

Chapter ii: How to Set Water Leaking from Your Water Softener

In that location are several reasons why water may be leaking from your water softener. These include:

• You accept a loose h2o line connexion

• You lot have a croaky water-carrying component

• You have a worn rotor valve seal

Solutions:

Before your begin, turn off the h2o supply to your water softener. It volition oft wait like an outdoor faucet. Turn it completely to the right to close off the period of h2o.

Turn off your water supply at the back of your softener before you lot begin

Loose water line connexion:

The water line connects your h2o softener to your water source. If the line has become loose, you may get water dripping from information technology. Tighten the connectedness with a wrench to see if that fixes your problem.

Cracked water-carrying component:

If yous discover whatever cracks in any of the components that acquit water to and from your softener such equally the bypass valve, then that role volition demand to be replaced. You should contact a professional to do this for you.

Worn rotor valve or water valve seal:

The rotor valve directs water through your water softener during the water softening bike and while flushing the resin filter. The rotor valve seal is located on the bottom of the rotor valve.

This seal stops water from leaking out of the valve and lets the water menstruation through the opening at the bottom of your rotor valve.

The seal may wear out over time and it will start to leak. If this happens, then it will need to be replaced.

Your rotor valve itself may eventually become defective and begin to leak water. It also may need to be replaced. Contact a professional to practise this for you.

Affiliate 3: How to Articulate Error Codes

Commonly, it is quite uncomplicated to clear the mistake codes from your Kenmore water softener.

Footstep ane: Expect upward the displayed error code in your owner's transmission to find the trouble shooting steps. If you no longer have your owner's manual, you can download ane online.

Stride 2: Unplug your water softener.

Step iii: Follow the steps outlined in your owner'southward manual for the particular error code.

Step 4: Plug your water softener back in.

Step v: Look 6 minutes after you have restored ability. If the error code returns, the problem wasn't resolved.

If you lot can't clear an error code by following the steps in your owner'south manual, contact a local professional person to aid fix your unit.

If you have lost your owner's manual, yous can download 1 online - Source: Sears Parts Direct

Chapter four: How to Clear Kenmore Error Code #one & #iii

Mistake lawmaking #ane, meaning a valve motor failure, is one of the more than common codes you will take displayed.

If your Kenmore water softener display is showing Error Code #1, yous can try the following:

Step 1: Unplug your softener and so plug it back in.

Step 2: Your softener will go through a exam fashion; information technology unremarkably takes nearly 8 minutes to become through this. This may solve your trouble.

Step 3: If you even so have Error ane after the test mode is complete, remove the top of your water softener and clean the valves, screens, and drains.

Pace iv: Unplug and plug your softener back in to run the exam mode again. If cleaning your softener has worked, so the Fault Code #1 will be gone.

Stride 5: If the error code is still there, and so check the switch within to see if it is working. Disconnect the switch and test information technology with a digital multi meter to come across if it is operating. If it isn't, so the switch will need to be replaced.

Step 6: If you are however getting an fault lawmaking, contact a professional who services Kenmore water softeners to repair it for you.

The following video volition take you through these steps in greater detail.

If you lot are getting Error Lawmaking #1, first attempt unplugging and plugging in your softener

Kenmore Error Code #3: If you are getting an Mistake code 3, it may exist that the switch (pictured below) needs replacing. Here are the steps to supercede this switch:

Footstep 1: Unplug the unit.

Footstep ii: Remove the lid of your softener and then you can run into the motor.

Step iii: The problem may be a faulty switch - unscrew the metallic plate at the elevation of your unit being conscientious not to dislodge the gasket in the center of the plate.

Step 4: Swing the metal plate effectually and then you can access the switch.

Step 5: Unscrew the 2 screws from the switch and popular it off

Step 6: Replace information technology with a new switch that you can order online

Step vii: Plug your unit back in to see if the error lawmaking has gone.

The post-obit video will show you lot the complete pace by step process.

Set Error Code iii with these unproblematic to follow steps

Chapter 5: What to Do if Your Kenmore Water Softener Has No Display

There are three main reasons why you lot may not have whatever display showing up on your Kenmore H2o Softener. These include:

• No power

• A failed power transformer

• A faulty timer

Solutions:

No Power:

Pace 1: Check that your h2o softener is fully plugged into the outlet and that it hasn't come up loose.

Step 2: If you notwithstanding don't have a brandish, unplug your water softener and plug in another small-scale detail, such every bit a lamp, into the same outlet to see if it works.

If the lamp doesn't light up, and so your issue is with the outlet itself and non your water softener. Check to see if a breaker needs to be flipped back on. If this doesn't work, you may demand to contact an electrician.

Step iii: If your outlet is working, then there must be something else wrong with the softener.

A Failed Ability Transformer:

Step ane: Unplug your transformer from the electric outlet.

Pace 2: Check the wiring connections from the transformer to the timer.

Footstep 3: Reconnect any wires that may have come loose.

Footstep iv: If your wiring connections are all okay, and so check all of the wires for whatever damage. If your wires are damaged, replace the transformer.

A Faulty Timer:

If your power and transformer are both okay, then your timer may exist faulty.

The timer is an electronic control board that allows you to program your water softener and lights up the display.

It also controls the h2o softening and resin filter flushing processes. If it isn't working, information technology will demand to be replaced.

Footstep 1: Put on piece of work gloves and unplug your h2o softener from its power source.

Footstep ii: Open the chapeau and release the ii front clips on the encompass. Lift the front end of the cover up and back to release the rear tabs and fully remove the cover.

Step 3: Release the locking tabs on the sides of the control panel and pull the command panel off.

Footstep four: Pull the low-cal for the salt storage tank up and out of the tank.

Stride five: Disconnect and remove the timer and pull information technology out of the control panel.

Footstep 6: Install a new timer and connect it to the command panel.

Pace 7: Supplant the cover and plug your h2o softener back in.

Step 8: Program your new timer by following the instructions in your owner's manual.

The post-obit video will step you through the process of replacing a Kenmore H2o Softener timer.

If your display isn't lighting up, your timer may need to
be replaced

Chapter half dozen: Proper Maintenance - How to Clean Your Kenmore Water Softener

Go along your unit running longer with proper water softener maintenance

Water Softener Maintenance: How to Clean Your Softener

Your Kenmore water softener will need to be cleaned from fourth dimension to time to keep information technology running properly and well maintained.

Y'all can take the following steps to clean your softener yourself:

Stride ane: Unplug your water softener.

Stride ii: Button in your bypass valve to re-directly the h2o then that it doesn't go into your softener.

Footstep three: Remove the lid of your softener.

Step four: Remove the nozzle and accept it apart to clean all of the pieces in warm, soapy water. You can remove and replace the two flow plugs with a toothpick to clean them equally well.

Step 5: Put all of the pieces of your nozzle back together again, replace the lid and plug in your softener.

Tip: as you are taking the components autonomously, lay them out in the gild that you took them out and so that you can hands recall the order to put them back together.

Tip: The flow plugs but go in ane way; make certain y'all place them dorsum in with the letter side facing upward.

The post-obit video volition testify in detail how to do the above steps.

Your water softener needs to be cleaned from fourth dimension to time

Water Softener Maintenance: How to Sanitize Your Softener

Over time, leaner could get into your water softener. If y'all suspect that this might be a problem, you can take the following steps to sanitize your water softener.

Step 1: Lift the common salt hole cover and fill the tank with up to 3 gallons of water or about 3 inches loftier.

Step 2: Take the chapeau off your brinewell and pour nigh 1 to 2 tablespoons of household bleach too known every bit chlorine bleach into the brinewell. Put the cover dorsum on.

Stride 3: Open up the bypass valve.

Step 4: Concord the ON/OFF-Agree button for 3 seconds to initiate the recharge cycle. The recharge bike volition empty the bleach into your softener to sanitize it. It will besides fill your salt tank to the appropriate level, remove the air from the resin tank, and ready your softener for service.

*Notation: It volition have well-nigh ii hours for your softener to go through the recharge cycle.

Water Softener Maintenance Tips and Tricks

1. Utilise merely pure salt, specially designed for water softeners. Never utilise regular table salt; it has besides many impurities.

2. Don't add more than salt until almost all of the salt has been used upward.

3. Don't add together likewise much time when you are refilling it. The salt level should come up upwards near two-thirds in your tank.

4. Clean your brine tank one time a year.

5. Before yous supersede a water softener, have it checked out to run into if it can exist repaired instead. Almost water softener repairs are relatively inexpensive.

Only use pure water softener salt in your Kenmore water softener Kitchener

Affiliate vii: Servicing Your Kenmore Water Softener

H2o Softener Maintenance Waterloo | H2o Softener Maintenance Kitchener

Like most home appliances, your water softener may need servicing or repairs at some signal.

At that place are a number of issues other than the ones listed above that can occur with your Kenmore water softener over time. One that is relatively easy to set yourself is a Salt span.

A salt bridge is a hard crust of salt that forms in the brine tank leaving an empty infinite between the h2o entering the tank and the salt itself.

Gently tapping on the side of your tank with a rubber mallet may dislodge the span for you, or you may demand to use a broom handle or other long object to become rid of the bridge. The following video will evidence you how.

Kenmore h2o softener Waterloo: Learn how to get rid of salt bridges

Other issues that can happen include:

• Blockages

• Seal kit needing replacing

• Faulty power supply

• Motor issues

• Resin bug and leaks

If yous would like help with these servicing issues, contact a local professional such every bit WaterSmart.

Kenmore Water Softener Owner'south Manuals

If you lot would like to attempt some small repairs or servicing for yourself, here are links to online Kenmore Water Softener Possessor'south manuals:

Kenmore Water Softener Professional Service

Kitchener, Waterloo, Cambridge, Guelph, St. Jacobs, Elmira, Woodstock & Surrounding Areas

Unfortunately, your Kenmore water softener tin can no longer be serviced or returned in stores every bit Sears has closed downwardly. Don't worry, however, yous tin can nonetheless contact a local professional who is capable of working with Kenmore h2o softeners.

If you lot alive in the Kitchener-Waterloo region, contact WaterSmart. WaterSmart has been servicing Kenmore water softeners for more than 25 years. Nosotros service all Kenmore water softener models.

If yous are having a problem with your softener, contact us and we can take a look at information technology and practise any necessary repairs at a reasonable rate.

WaterSmart Service Area

• Kenmore water softener maintenance Kitchener

• Kenmore h2o softener maintenance Waterloo

• Kenmore water softener maintenance Cambridge

• Kenmore h2o softener maintenance Guelph

• Kenmore water softener maintenance St. Jacobs

• Kenmore h2o softener maintenance Elmira

• Kenmore water softener maintenance Woodstock

WaterSmart: For Kenmore Water Softener Repairs and Service

If you own a Kenmore water softener, you tin trust WaterSmart for all of your repairs and maintenance.

WaterSmart has been servicing all brands of water softeners for more than 25 years. Nosotros are your local water softener and plumbing experts in the Kitchener-Waterloo region.

We're proudly jubilant 25 yr of professional person service and we would love to put our noesis and expertise to work for you. If you are looking for a new water softener, or you lot require servicing for your existing unit of measurement, contact the states today!

WaterSmart likewise offers a full range of plumbing services that include, merely are non limited, to:

• Kitchens and Bathrooms

• Leaks

• Toilets and Taps

• Chock-full or Dull Drains

• Countertop Pre and Mail service Installation

• Dishwasher Installations

• Sump Pumps

• Tankless Hot Water Heaters

• New Plumbing and Renovations

• Master Plumber and Gas Fitter

• Backflow Testing or Device Installation

Relieve up to $250.00 on our 25th
Anniversary Sale

Right now, we accept some great deals on Water Softeners!

Become our Smart Series thirty, regularly $1,295.00 for just $ane,195 plus HST - Relieve $100.00, or Our 25th Anniversary Tahoe Series xxx, for but $1,345 plus HST, regularly $one,595.00 -Save $250.00 and pay using 12 Equal payments with No Interest!

Here's what WaterSmart customers are proverb:

"My married woman and I recently purchased a dwelling house that did not have a water softener since the firm was built.…They are very skilled professionals and have not bad customer service. We also bought a opposite osmosis from them. They gave us detailed instructions on how to operate the softener and reverse osmosis. I would recommend these guys. Give thanks yous Watersmart…[Read more]"

-

William

Read more testimonials here

Source: https://www.watersmartsystems.com/blog/2019/8/27/kenmore-water-softener-troubleshooting-servicing

Share this post